Tuesday, June 24, 2008

Modify PAL Atari 2600 for S-Video output.

I got an Atari 2600 from ebay some time last year 2006. It's one of those "vader" editions. Unlike the one I had growing up (which was a NTSC model from the US), this one is a PAL model. After hooking up the antenna to the TV, I was ready to play some retro games... or so I thought.

The PAL unit came with an IEC 169-2 connector (no it wasn't RCA). I did recall that the NTSC unit came with a TV/GAME switch box so that you can choose between antenna to watch TV or your game but the PAL unit didn't come with one. The back of the TV also had the same anttena connector so I just plugged it in.

Then I spent hours trying to tune the TV to get the picture to come out clear... I tried all the different PAL systems and B/G came out the best (others had bad/no audio, no colour, etc). The best picture I got was washed out, and had some snow in the background.





Now, I was thinking that somewhere inside the unit the console probably works with some kind of composite signal, and it might just have a bad RF modulator. Or maybe the coax cable was shot? At any rate I looked around the internet for a possible "video out" solution. I found something better. S-Video. From this site: http://www.atariage.com/2600/faq/index.html?SystemID=2600#composite, a circuit was published. This isn't exactly the simplest of circuits, there's 2 other solutions I found, one involves just a bunch of resistors, and the other was the same mod without the IC. But where's the fun in that? Besides this circuit also isolates the video circuit from the 2600's circuits, so if I were to do something stupid, like feed the s-video port some voltage, or hook it up to an ADB (apple desktop bus) port, it will only affect the video circuits I added. Plus, it doesn't put any load on the circuits like the other mods.
Since the article already explains what you need to do in detail, I'm not going to repeat all of that here. After obtaining the required materials this is how it ended up looking. This was the original RF cabling, internally it was RCA:


This was the main board with the shielding in place:

You have to untwist 5 of these to remove the shielding:

I used wire wrap wire to connect the circuit to the connection points. I did not make any changes to the existing circuit so i can revert it back to the original condition if I ever decide:



I made the output cable long, like the original RF cable so you can pull the console far from the TV, since the controller cables are so short.


It's time to hook it up to the TV


Now the moment of truth:







That was definitely a lot better than the RF cable. Well I have to assemble the unit back together and try out some other games:

Monday, June 23, 2008

Rebuild a laptop Li-ion battery pack

Warning!!! If you are not completely sure what you are doing, don't apply what is described below. In any case I am not responsible in any way to the consequences that this guide may have. Read it at your own risk. Please do not proceed if you don't agree with the above.

After having read a different how-to article on the same topic:

I decided to do some repairs on a similar laptop. This was a Fujitsu Lifebook S6120. The battery wouldn't charge anymore and after 5 to 10 minutes of attempting to charge it the onboard LCD displays a "shorted battery" error:



So, following the directions in the electronics-lab article, I proceeded to disassemble the battery:

Unfortunately for me, it contained very different cells. And to make things worse, there are no markings on the cells whatsoever, just (what seems to be) red shrink tube and some tape:

After doing some research I found out that these cells are called "18650 Lithium-ion cells". A few more searches and I found a company selling them:


Make sure you order the non-protected ones as the protected ones have a built in circuit that cuts off power when you go below a certain voltage, this circuit is already part of the battery pack and would probably cause problems if you have two of them.

After waiting around 2 weeks, this arrived in the post:

The package arrived opened so customs must have x-rayed it and checked it just to make sure. (It might look like dynamite in the x-ray, who knows, better safe than sorry).
Now, slowly pry out the old batteries, there are some double-sided tape holding them to the battery pack case:



Test fitting it just to make sure it does (fit):


After taking more pictures and noting down the polarity of the original batteries:



It's time to take the whole thing apart. Use a screwdriver and/or pliers to remove all the connectors. Try your best to keep them all intact:


Next would be to transfer all the tapes and insulators to the new batteries (keep them the same way you took them off). The next part involves attaching the connectors back on the batteries, ideally you would use a device for welding the tabs to the cells, but I don't have one of those. Instead I am going to solder them to the battery. I have read a lot of warnings that extreme heat (like that from a soldering iron) can destroy a lithium-ion battery and even cause explosions. What I did was wrap the cells in a moist cloth and not apply more heat than necessary. I also sanded down the contacts and applied soldering paste before soldering. I REPEAT: If you apply too much heat for too long, you could destroy the cells and/or cause an explosion. Ok, with the unpleasant stuff out of the way, we connect the cells the same way we took the connectors off the original cells:





Then put them back in the battery pack case. Note that because the solder was a tad thicker than what was originally there, you might have to force them in. There should be enough space there to still fit the new cells in. Note that you have to return all the insulators/cardboard pieces back where they came from. In the last photo above, this will cause a short (and a possible explosion) if you do not.

Then, to glue the case back together, I applied a small amount of epoxy all around the are and pressed it down with a phone book.



That's it. After plugging the battery in, it's working again. I also did a battery recalibration so that ACPI would show the correct charge level. This varies with different laptops and have their own recalibration procedures, but generally, you turn off all energy saving settings and fully charge the battery and leave it plugged 2 to 3 hours even after it says full. Then completely discharge it until the laptop turns off. Note that this will not damage the battery since at 0% reading the cells actually still have some charge left in them but the protection circuit cuts it off before real damage happens.